Introduzione: La tendenza è quella di avere quantità di campione dalle dimensioni sempre minori e controllate ma comunque rappresentative.
Nell’analisi dei materiali solidi certamente non si applica il detto popolare “più grande è meglio”. L’obiettivo è produrre particelle sufficientemente piccole da soddisfare i requisiti delle analisi, garantendo nel contempo una rappresentazione accurata del materiale originale. Le “particelle” d’interesse per l’analista vanno generalmente da 10 µm a 2 mm, ma in molte applicazioni sono necessarie granulometrie ancora più fini. Un esempio sono i principi attivi, dove è necessario operare nel range dei submicron. Infine, per l’estrazione di DNA ed RNA, la tecnica della lisi cellulare è già ben consolidata.
Gli scienziati hanno studiato le nano particelle (particelle estremamente piccole con meno di 100 nanometri di diametro) per molti anni. A proposito delle nano particelle, sono state sviluppate nuove ed innovative proprietà, es. semiconduttive o superficiali, cosi come l’effetto Lotus che ha aperto possibilità fino ad ora inaspettate. Esistono diversi metodi per produrre nano particelle. La tecnica “bottom up” coinvolge la sintesi delle particelle da atomi e molecole. Con il metodo “top down”, le particelle vengono ridotte a dimensioni nanometriche tramite la macinazione. Lo strumento adatto per questa applicazione è il mulino planetario a sfere, come i RETSCH PM 100, PM 200, PM 400 che forniscono il necessario input di energia per la macinazione fino a dimensioni nanometriche.
The use of pesticides in agriculture makes it possible to plant extensive mono cultures and often leads to substantial yield increases of food and feed crops. Demand and application have grown steadily over the years, leading to increased contamination of the soil due to the toxic nature of pesticides. Soils save the toxins and their decomposition products so that wildlife is also affected by them. Among the undesired side effects are damages to useful plants and insects like bees. The wind carries pesticides to uncontaminated areas such as fields used for organic farming. Rain also transports the chemicals away from their original area of application to waters and groundwater. Although in most cases the limit values for particular pesticides and their decomposition products are not exceeded, the cumulative effect on humans and animals has not been thoroughly investigated so far. The possible accumulation of pesticides in the food chain could be a source of health hazards; therefore strict quality control of soils is indispensable.
How are nano particles produced? The “Bottom-Up” method synthesizes particles from atoms or molecules. The “Top-Down” method involves reducing the size of larger particles to nanoscale, for example with laboratory mills. Due to their significantly enlarged surface in relation to the volume, small particles are drawn to each other by their electrostatic charges. Nano particles are produced by colloidal grinding which involves dispersion of the particles in liquid to neutralize the surface charges. Both water and alcohol can be used as dispersion medium, depending on the sample material. Factors such as energy input and size reduction principle make ball mills the best choice for the production of nanoparticles.
Reliable and accurate analysis results can only be guaranteed by reproducible sample preparation. This consists of transforming a laboratory sample into a representative part sample with homogeneous analytical fineness. Retsch offers a comprehensive range of the most modern mills and crushers for coarse, fine and ultra-fine size reduction of almost any material. The product range also comprises a wide choice of grinding tools and accessories which helps to ensure contamination-free preparation of a great variety of sample materials. The selection of the correct grinding tool depends on the sample material and the subsequent method of analysis. Different grinding tools have different characteristics, such as required energy input, hardness or wear-resistance.
Alloys such as amalgam in dental medicine or stainless steel are universally known and used. The traditional way to produce alloys is to fuse the components at very high temperatures. If only small quantities are required or if the alloys cannot be fused by melting mechanical alloying is an alternative. For this application ball mills are ideally suited. They provide a high energy input due to the impact and friction effects which occur during grinding.
Use of laboratory grinders for size reduction of human bones and bioceramics
Bone implants and substances for bone regeneration are used in surgery to replace degenerated bone material by implants or to “re-build” it with specific substances. The material used in implants varies from autogeneic (supplied by the patient) through allogeneic (supplied by a donor) bones to replacement materials such as hydroxylapatite (HA) and tricalcium phosphate (TCP). Bovine bones and corals are used in conjunction with synthetically produced foamed materials to form a basis for the regeneration of bone substance. Various RETSCH mills are suitable for the preliminary and fine grinding of human bones as well as bioceramic materials.
A variety of methods can be used to analyze solid materials. What they all have in common is the necessity to use a representative, homogeneous analysis sample which needs to have a particular fineness, depending on the analytical method used. The size reduction and homogenization of solids is usually carried out with laboratory crushers and grinders.
A faultless and comparable analysis is closely linked to an accurate sample handling. Only a sample representative of the initial material can provide meaningful analysis results. Rotating dividers and rotary tube dividers are an important means to ensure the representativeness of a sample and thus the reproducibility of the analysis. Correct sample handling consequently minimizes the probability of a production stop due to incorrect analysis results. Thus correct sample handling is the key to effective quality control.
The preparation of a mixture of organic and inorganic samples holds some difficulties: whereas sand, clay and stones can usually be ground to homogeneous samples with suitable laboratory mills, the high energy input can cause samples with organic components such as fat or starch to cake. Carsten Bunn, a laboratory technician at the waste water treatment laboratory BRW, has to deal with this problem every day. He treats samples which are taken from the sand traps of the wastewater treatment plants and consist of exactly that mixture. The sediments of household and industry waste water not only contain sand, clay or leaves but anything that people nowadays dispose of through the sewer system: cellulose, hair and especially food residues.
Mechanochemistry is a very effective method to carry out syntheses without solvents and by-products. The technical literature describes a great number of reactions where a conversion of 100% is achieved. A precondition for the establishment of mechanochemistry in the industrial sector is the availability of suitable laboratory mills. A decisive factor is that – similar to conventional preparative chemistry – ambient parameters such as pressure and temperature can be documented and monitored. The Planetary Ball Mills and Mixer Mills from Retsch fulfill these requirements.